Electro-Voice Q44 650 W per channel power amplifier EV-Q44 EV-Q44

EV-Q44
0.00 2040-01-02 USD InStock
Weight: 29 lb
Brand: Electro-VoiceElectro-Voice

Call for price : 973-731-7131

Contact us for more information


With the Q44 650 watt per channel power amp, Electro-Voice proves that there are also audible differences in addition to power output differences in their amps.

Dynamic Headroom

Amplifier power and distortion figures are typically specified with sine wave signals. However, music signals are far more dynamics than sine waves, comprising a pulsed wideband spectrum.

EV believes that, above all figures, the tonal performance of live music counts most; therefore, all of their amplifiers are designed for dynamic headroom. This means that each and every EV amp has at least 30% more output capability for short-term signals, when compared to a long-term sine wave value. This additional headroom results in an amp that will, for example, allow for short term signal peaks of at least 780W when spec'd 600W.

While dynamic headroom is audible when playing music through a sound system, another specification to observe is the increase in output power from an 8 ohm load to 4 ohms, and then down to 2 ohms. Of course, all Electro-Voice amplifiers are designed to be absolutely stable into loads of 2 ohms.

Transient Response

When processing dynamic signals, other important criteria are signal speed and dynamic distortion. For example, kick drum signals carry pulses of many frequencies as an overlay spectrum. Therefore, and in contrast to many other manufacturers, EV specifies a lot more information on their amplifiers' dynamic behavior than just "slew rate" figures. Important tests referring to the amp's ability regarding multitone signal pulses are expressed by IMD-SMPTE measurements at high power levels. And, while IMD tests show the Intermodulation Distortion behaviour (how much "sound" is added by the ampifier), DIM30 is the real spec for speed in an amplifier. All these tests are carried out in EV labs during an amplifier's design phase, to ensure maximum sonic performance. While these technical explanations appear very complex, they are clearly audible. Take a Q Series amplifier and crank it up - you'll hear the difference immediately.

Protection Package & Dynamic Limiter

There are many good-sounding amplifiers available; however, for an amp to be considered the world's best requires unparalleled reliability in real-world applications.

Q Series amplifiers benefit from decades of professional amplifier design, and all the expertise that has made EV amps the concert/touring standard is built into Q Series. Our complete protection package includes sophisticated circuits against overheating, short circuit, DC output voltage, HF oscillation, back EMF (Electromotive Force), and destructive peak current.

Furthermore, Q Series amps also protect your valuable loudspeakers with built-in dynamic limiters, preventing dangerous output clipping. The limiters immediately reduce amp gain when dynamic headroom is pushed to the limits at maximum output, keeping distortion below 1% in a situation that can otherwise cause a signal to clip, which is often fatal for woofers and drivers.

Q-Series Amplifiers & Connectivity

Whatever application you choose, you can be sure your Q Series amp is prepared:

  • Both inputs have a paralleled loop thru XLR output toroute signal to other amp inputs
  • Besides the usual channel A & B outputs viaSpeakon connectors (on pin 1+/1-), output A carries the signal of channel B aswell (on pin 2+/2-), providing an easy drive option for biamped speakers
  • Parallel & Bridge Mode option switches provideadditional functionality with minimized cabling requirements
  • An additional switchable LPN (Low-Pass Notch) filter provides extra tonalfundament and kick, with protective Low-Cut for using smaller passive 12" or15" cabinets without additional subwoofers

 

Amplifier Gain

32 dB

Continuous Rated Power (1 kHz, THD 1%) 2Ω

650 Watts

Continuous Rated Power (1 kHz, THD 1%) 4Ω

450 Watts

Continuous Rated Power (1 kHz, THD 1%) 8Ω

270 Watts

Continuous Rated Power (20-20 kHz, THD<0,2%) 4Ω

400 Watts

Continuous Rated Power (20-20 kHz, THD<0,2%) 8Ω

200 Watts

Cooling

Front-to-Rear, 3-stage fans

DIM 30

0.05%

Electronics Type

Amplifier

Frequency Response

10 Hz - 40 kHz ±1 dB

Impedance

2/4/8 Ω

Input Impedance (Balanced)

20 kΩ

Input Sensitivity

+2.2 dBu

Intermodulation Distortion (SMPTE)

0.1%

Maximum Bridged Output 4Ω

1300 Watts

Maximum Bridged Output 8Ω

900 Watts

Maximum Input Voltage

+21 dBu 8.69 Vrms

Network Control (IRIS-Net)

No

Signal-to-Noise Ratio (A-weighted)

106 dB

Slew Rate

25 V/µs

Topology

Class-AB

Total Harmonic Distortion

0.03%

Height

2RU 88.1 mm (3.47")

Width

483 mm (19.02")

Depth

421.5 mm (16.59")

Weight Net

12.6 kg (27.78 lbs)

Brand URL : http://www.electrovoice.com/product.php?id=756

Connect With dB Sound Store Today

Please contact dB Sound Store using the Contact form to the right. We will respond to you quickly by email or telephone regarding Sound Equipment purchases, maintenance, repair, custom Sound System Design and expert installations. Let us know how we can help you today!

 
Since 1992, dB Sound Store has worked with some of the biggest artists, producers and commercial studio owners in the music industry to meet all of their diverse needs. The extensive client list of top industry professionals speaks to dB Sound's commitment to excellence. Unlike many of our competitors we listen to what you want, provide it at a reasonable cost and support the end result long after the job is finished.  OUR CLIENT LIST
 
dB Sound Store, LLC
33 Yale Terrace
West Orange
New Jersey, 07052
Call Us: 973-731-7131

Contact dB Sound Design